Wood wax oil painting solid wood furniture sample process
Today, we will take wood wax oil as the object of practical test, at the same time, the PU paint painted board as a reference, and then two samples of white blanks painted with wood wax oil to compare the effect, see the final comparison between the painted wood wax oil samples and the reference board you will know the magic of wood wax oil.
1
Material preparation:
Reference board (dark brown color on the right side painted with PU paint) and white blank sample.
Wood wax oil (choose genuine wood wax oil products), special thinner, color paste (can be selected according to the color of the reference board).
Special sponge brush, equipment for opening the can, small straw, gloves.
Sandpaper (180#-320#, 600#-1000#), sanding board, lint-free cotton cloth, pen, color paste cup, chopsticks.
2
White blank sample sanding
Connoisseurs often say that the so-called “three points by painting, seven points by sanding”, so before painting, sanding this step is crucial. Sample blank surface sanding must be sanded to a smooth surface, if the surface sanding is not flat and smooth enough, then it will lead to the painting of the surface roughness and harshness is not flat enough, and even affect the overall color tone of the consequences of unevenness. Therefore, sanding is very important, you can consider using 180 # sandpaper rough grinding surface and then use 1000 # sandpaper fine grinding surface, and then use a cotton cloth to remove the surface sanding powder and wood powder can be clean.
3
Sample Comparison Method
In order to better do the effect of comparison, so the need for each sample board separated into two parts of use, the best way is to use a ruler to measure the line, and then use transparent adhesive tape cooperation for the separator line can be (here the separator line is designed to facilitate the consumers to do the comparison, and construction tutorials have nothing to do with the DIY people do not need to learn the sub-steps).
4
Color paste selection
Can be based on the reference board of wood wax oil painted in the color palette compared to the reference board painted with PU paint to select the color paste, the following chart in the comparison, can choose the standard color paste for the three samples (walnut, yellow pear, teak), and a three-color tones and the color paste for the black, red maple, yellow sandalwood, which is the weight ratio of 1:3:6.
5
Wood wax oil and color paste blending (weight ratio of 10:1)
Positive color paste weight weighing, because here you need to do the sample for small-scale production, the need for the use of the dose to achieve accurate comparison, so here you need to use to the pipette filling and accurate electronic weighing, and strictly do a good job of the sample dose ratio of the reconciliation. Mixed color paste dosage needs to be stirred evenly before use, if used for a long time will form a precipitate and affect the color painting uneven phenomenon.
6
Combination of color paste and wood wax oil
After mixing the blended color paste evenly, add wood wax oil to stir and blend, it should be noted that the weight ratio of wood wax oil and color paste is 10:1, if the volume ratio of 1 barrel of 2.5L of wood wax oil dosage to add 2 100ml of color paste can be added, if you do not need to be too thick in terms of color concentration, add 1 100ml can be added, when the four kinds of color paste is completely blended and finished, it can be put into the When the four kinds of color paste are completely blended, it can be put into painting use.
7
First painting (kneading method)
There are three times of brushing, the first two times are purely for coloring process, and the last time is to use varnish for covering. Of course, you can also do two brushes, but the effect of three brushes will be better. And in order to ensure that the wood wax oil painting effect, when painting must be thin brush.
Then, the first painting needs to use the kneading brush method, you need to mix the color paste of the wood wax oil poured on the sample board and then use the cotton cloth without lint to knead the brush clockwise, so that the wood wax oil can better penetrate into the deep layers of the wood, the formation of a protective effect is also more reflective of the wood itself, the sense of texture. At the end of the rubbing brush, you need to rub along the wood grain texture (here you need to use the rubbing method), then placed in a well-ventilated environment for air drying, 24 hours before the second painting.
Look at the picture below how the first rubbing of the four color paste in two samples after the effect? Isn’t it great?
8
Second painting (brush method)
Place a day after the sample board has been dry enough to carry out the second painting, in the painting before the use of 1000 # sandpaper on the surface of the surface to sand the surface smooth and flat, in the use of lint-free cotton cloth to clean up the surface can be carried out after the second painting.
Remember, the dosage of wood wax oil and color paste for the second painting are the same as the proportion of the first painting.
The second coat should be applied with a thin sponge, following the grain of the wood.
After the second brush, the effect is actually enough to show, and the effect is very close to the reference board. Finally, the same placed in a well-ventilated environment for 24 hours to dry, you can do the final end of the work.
9
Final painting (varnish overlay)
Before the third painting, the surface of the sample board should be sanded, using 1000# sandpaper.
Translated with www.DeepL.com/Translator (free version)